Heat Pumps

Thermino iPV uses an external heating source (e.g. a boiler) as a main source of heat, and surplus PV energy to provide an AC power supply, which is supplied to the electric heater inside the Heat Battery. This is a great way to add water storage and increase the self-consumption of a PV system. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. Only the Myenergi Eddi can be used as an immersion controller at present. The Thermino 300 iPV would typically be installed in a 4-5 bedroom property. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty. Power Inputs:  Grid electricity - Secondary SourceBoiler - Primary SourceSolar Panels - Secondary SourceHeat Pump - Some high temp   General Specifications Product Code DKP-DBW-ATZ-1 Equivalent energy storage 14.0kWh Equivalent hot water capacity 284L Water available at 40°C 370L Weight in use 233kg Height 1050mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 35W Energy efficiency rating A+ Recommended flow rate 25LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Connected load at 230v, 50hz 2,800W

Read more less

Thermino iPV uses an external heating source (e.g. a boiler) as a main source of heat, and surplus PV energy to provide an AC power supply, which is supplied to the electric heater inside the Heat Battery. This is a great way to add water storage and increase the self-consumption of a PV system. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. Only the Myenergi Eddican be used as an immersion controller at present. The Thermino 210 iPV would typically be installed in a 3 bedroom property.   Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty. Power Inputs:  Grid electricity - Secondary SourceBoiler - Primary SourceSolar Panels - Secondary SourceHeat Pump - Some high temp   General Specifications Product Code DKP-DBW-ATZ-1 Equivalent energy storage 10.5kWh Equivalent hot water capacity 212L Water available at 40°C 300 Weight in use 187kg Height 870mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 32.1W Energy efficiency rating A+ Recommended flow rate 20LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Connected load at 230v, 50hz 2,800W

Read more less

Thermino iPV (UniQ HW +iPV) uses an external heating source (e.g. a boiler) as a main source of heat, and surplus PV energy to provide an AC power supply, which is supplied to the electric heater inside the Heat Battery. This is a great way to add water storage and increase the self-consumption of a PV system. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. Only the Myenergi Eddi an be used as an immersion controller at present. The Thermino 150 iPV would typically be installed in a 1-2 bedroom property. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty. Power Inputs:  Grid electricity - Secondary SourceBoiler - Primary SourceSolar Panels - Secondary SourceHeat Pump - Some high temp   General Specifications Product Code DKP-DBW-ATZ-1 Equivalent energy storage 7.0kWh Equivalent hot water capacity 142L Water available at 40°C 185L Weight in use 136kg Height 640mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 28.1W Energy efficiency rating A+ Recommended flow rate 15LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Connected load at 230v, 50hz 2,800W

Read more less

 Thermino i - Designed to produce domestic hot water by using an external heating source (e.g. a boiler) as a main source of heat, this range of heat batteries has a standby heating element built in to act as a backup if the main heat source fails. It can be used as an alternative to a hot water storage tank, providing the same energy storage in a much smaller volume. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 300 i would typically be installed in a 4-5 bedroom property. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty.   Power Inputs: Grid electricity Secondary Source Boiler Primary Source Solar Panels Heat Pump Some high temp General Specifications Product Code DRP-CBW-AVZ-1 Equivalent energy storage 14.0kWh Equivalent hot water capacity 284L Water available at 40°C 370L Weight in use 233kg Height 1050mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 35W Energy efficiency rating A+ Recommended flow rate 25LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Connected load at 230v, 50hz 2,800W

Read more less

  Thermino i - Designed to produce domestic hot water by using an external heating source (e.g. a boiler) as a main source of heat, this range of heat batteries has a standby heating element built in to act as a backup if the main heat source fails. It can be used as an alternative to a hot water storage tank, providing the same energy storage in a much smaller volume. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 210 i would typically be installed in a 3 bedroom property. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty.   Power Inputs: Grid electricity Secondary Source Boiler Primary Source Solar Panels Heat Pump Some high temp General Specifications Product Code DNP-CBW-AVZ-1 Equivalent energy storage 10.5kWh Equivalent hot water capacity 212L Water available at 40°C 300L Weight in use 187kg Height 870mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 32.1W Energy efficiency rating A+ Recommended flow rate 20LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Connected load at 230v, 50hz 2,800W

Read more less

  Thermino i - Designed to produce domestic hot water by using an external heating source (e.g. a boiler) as a main source of heat, this range of heat batteries has a standby heating element built in to act as a backup if the main heat source fails. It can be used as an alternative to a hot water storage tank, providing the same energy storage in a much smaller volume. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 150 i would typically be installed in a 1-2 bedroom property. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty.   Power Inputs: Grid electricity Secondary Source Boiler Primary Source Solar Panels Heat Pump Some high temp General Specifications Product Code DKP-CBW-AVZ-1 Equivalent energy storage 7.0kWh Equivalent hot water capacity 142L Water available at 40°C 185L Weight in use 136kg Height 640mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 28.1W Energy efficiency rating A+ Recommended flow rate 15LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Connected load at 230v, 50hz 2,800W

Read more less

  Thermino i - Designed to produce domestic hot water by using an external heating source (e.g. a boiler) as a main source of heat, this range of heat batteries has a standby heating element built in to act as a backup if the main heat source fails. It can be used as an alternative to a hot water storage tank, providing the same energy storage in a much smaller volume. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 70 ePV would typically be installed in a studio apartment, or for off-grid applications in a caravan or boat. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty.   Power Inputs: Grid electricity Secondary Source Boiler Primary Source Solar Panels Heat Pump Some high temp   General Specifications Product Code DGP-CBW-AVZ-1 Energy capacity 3.2kWh Equivalent hot water capacity 71L Water available at 40°C 85L Weight in use 79kg Height 440mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 20W Energy efficiency rating C Recommended flow rate 6LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Connected load at 230v, 50hz 2,800W

Read more less

  Thermino ePV - Designed to produce domestic hot water by using grid electricity and surplus PV energy. It can be used as an alternative to a hot water storage tank, providing the same energy storage in a much smaller volume. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 300 ePV would typically be installed in a 4-5 bedroom property. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty.   Power Inputs:  Grid electricity - Secondary sourceBoilerSolar Panels - Primary SourceHeat Pump   General Specifications Product Code DRP-BAW-ATY-1 Equivalent energy storage 14.0kWh Equivalent hot water capacity 306L Water available at 40°C 436L Weight in use 233kg Height 1050mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 35W Energy efficiency rating C Recommended flow rate 25LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Annual electricity consumption 2,701kWh/annum

Read more less

Thermino ePV - Designed to produce domestic hot water by using grid electricity and surplus PV energy. It can be used as an alternative to a hot water storage tank, providing the same energy storage in a much smaller volume. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 210 e would typically be installed in a 3 bedroom property as a rule of thumb. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty.   Power Inputs:  Grid electricity - Secondary sourceBoilerSolar Panels - Primary SourceHeat Pump General Specifications Product Code SNP-BAW-ATY-1 Equivalent energy storage 10.5kWh Equivalent hot water capacity 212L Water available at 40°C 301L Weight in use 178kg Height 870mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 32W Energy efficiency rating C Recommended flow rate 20LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Annual electricity consumption 2,690kWh/annum  

Read more less

  Thermino ePV (UniQ eHW +iPV) - Designed to produce domestic hot water by using grid electricity and surplus PV energy. It can be used as an alternative to a hot water storage tank, providing the same energy storage in a much smaller volume. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 150 ePV would typically be installed in a 1-2 bedroom property as a rule of thumb. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty.   Power Inputs:  Grid electricity - Secondary sourceBoilerSolar Panels - Primary SourceHeat Pump General Specifications Product Code SKP-BAW-ATZ-1 Equivalent energy storage 7.0kWh Equivalent hot water capacity 140L Water available at 40°C 199L Weight in use 139kg Height 640mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 28.1W Energy efficiency rating C Recommended flow rate 15LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Annual electricity consumption 1,398kWh/annum

Read more less

Thermino 70 ePV - Designed to produce domestic hot water by using grid electricity and surplus PV energy. It can be used as an alternative to a hot water storage tank, providing the same energy storage in a much smaller volume. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 70 ePV would typically be installed in a studio apartment, or for off-grid applications in a caravan or boat. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty.   Power Inputs:  Grid electricity - Secondary sourceBoilerSolar Panels - Primary SourceHeat Pump General Specifications Product Code SGP-BAW-ATZ-1 Energy capacity 3.2kWh Equivalent hot water capacity 74L Water available at 40°C 105L Weight in use 79kg Height 440mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 20W Energy efficiency rating C Recommended flow rate 6LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Annual electricity consumption 542kWh/annum

Read more less

 Thermino e - Designed to produce domestic hot water and is heated directly by grid electricity only. This can be used as a space saving and flexible alternative to a hot water tank with an immersion heater. When combined with a charge timer and a variable electricity tariff, the Thermino e range allows for low cost electric water heating. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 300 e would typically be installed in a 4-5 bedroom property.   Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty. Power Inputs: Grid electricity Boiler Solar Panels Heat Pump   General Specifications Product Code DRP-AAW-AVZ-1 Equivalent energy storage 14.0kWh Equivalent hot water capacity 306L Water available at 40°C 436L Weight in use 233kg Height 1050mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 35W Energy efficiency rating C Recommended flow rate 25LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Annual electricity consumption 2,701kWh/annum

Read more less

  Thermino e - Designed to produce domestic hot water and is heated directly by grid electricity only. This can be used as a space saving and flexible alternative to a hot water tank with an immersion heater. When combined with a charge timer and a variable electricity tariff, the Thermino e range allows for low cost electric water heating. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 210 e would typically be installed in a 3 bedroom property as a rule of thumb. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty. Power Inputs: Grid electricity Boiler Solar Panels Heat Pump   General Specifications - Product Code SNP-AAW-AVZ-1 Equivalent energy storage 10.5kWh Equivalent hot water capacity 212L Water available at 40°C 301L Weight in use 178kg Height 870mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 32W Energy efficiency rating C Recommended flow rate 20LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Annual electricity consumption 2,690kWh/annum

Read more less

Thermino e - Designed to produce domestic hot water and is heated directly by grid electricity only. This can be used as a space saving and flexible alternative to a hot water tank with an immersion heater. When combined with a charge timer and a variable electricity tariff, the Thermino e range allows for low cost electric water heating. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 150 e would typically be installed in a 1-2 bedroom property as a rule of thumb. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty. Power Inputs: Grid electricity Boiler Solar Panels Heat Pump   General Specifications Product Code SKP-AAW-AVZ-1 Equivalent energy storage 7.0kWh Equivalent hot water capacity 142L Water available at 40°C 199L Weight in use 139kg Height 640mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 28W Energy efficiency rating C Recommended flow rate 15LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Annual electricity consumption 1,398kWh/annum

Read more less

Thermino e - Designed to produce domestic hot water and is heated directly by grid electricity only. This can be used as a space saving and flexible alternative to a hot water tank with an immersion heater. When combined with a charge timer and a variable electricity tariff, the Thermino e range allows for low cost electric water heating. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 70 ePV would typically be installed in a studio apartment, or for off-grid applications in a caravan or boat. Note, the Sunamp is very heavy:   Tilting it beyond 45 degrees may damage the unit and void your warranty. Power Inputs: Grid electricity Boiler Solar Panels Heat Pump   General Specifications Product Code SGP-AAW-AVZ-1 Equivalent energy storage 3.2kWh Equivalent hot water capacity 74L Water available at 40°C 105L Weight in use 79kg Height 440mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 20W Energy efficiency rating C Recommended flow rate 6LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Annual electricity consumption 542kWh/annum

Read more less

This is included in Telfords range of indirect heat pump cylinders, designed specifically to operate with a range of air source heat pumps. These are available in a range sizes between 150-500L capacity. They do not include a 3-port valve and this must be purchased separately.  Featuring a purpose-designed coil with a 2m² surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders are supplied with a factory-fitted 3 kW immersion heater to provide back-up heat. Duplex stainless steel provides superior corrosion resistance 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied (details below) Fully insulated to minimise any heat loss Twin coil option available for use with a traditional boiler and solar thermal Lifetime manufacturing warranty on inner container (2 years on components)* Renewable and bespoke options available   Cylinder Specifications Capacity: 250L Weight (empty): 40kg Weight (full): 288kg Height: 1800mm Diameter: 554mm Coil size: 3m² Product Details Product code TSMI250/HP Standing heat loss 2.00 kWh/24h Max supply pressure 12bar Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Included Components 3kW immersion heater T&P relief valve Acetal Tundish Inlet group control 2-port valve External expansion vessel Dual probe thermostat

Read more less

This is included in Telfords range of indirect heat pump cylinders, designed specifically to operate with a range of air source heat pumps. These are available in a range sizes between 150-500L capacity. They do not include a 3-port valve and this must be purchased separately.  Featuring a purpose-designed coil with a 2m² surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders are supplied with a factory-fitted 3 kW immersion heater to provide back-up heat. Duplex stainless steel provides superior corrosion resistance 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied (details below) Fully insulated to minimise any heat loss Twin coil option available for use with a traditional boiler and solar thermal Lifetime manufacturing warranty on inner container (2 years on components)* Renewable and bespoke options available Cylinder Specifications Capacity: 200L Weight (empty): 36kg Weight (full): 230kg Height: 1500mm Diameter: 554mm Coil size: 3m² Product Details Product code TSMI200/HP Standing heat loss 1.85 kWh/24h Max supply pressure 12bar Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Included Components 3kW immersion heater T&P relief valve Acetal Tundish Inlet group control 2-port valve External expansion vessel Dual probe thermostat

Read more less

This is included in Telfords range of indirect heat pump cylinders, designed specifically to operate with a range of air source heat pumps. These are available in a range sizes between 150-500L capacity. They do not include a 3-port valve and this must be purchased separately.  Featuring a purpose-designed coil with a 2m² surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders are supplied with a factory-fitted 3 kW immersion heater to provide back-up heat. Duplex stainless steel provides superior corrosion resistance 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied (details below) Fully insulated to minimise any heat loss Twin coil option available for use with a traditional boiler and solar thermal Lifetime manufacturing warranty on inner container (2 years on components)* Renewable and bespoke options available Cylinder Specifications Capacity: 170L Weight (empty): 34kg Weight (full): 202kg Height: 1200mm Diameter: 510mm Coil size: 2m² Product Details Product code TSMI170/HP Standing heat loss 1.94 kWh/24h Max supply pressure 12bar Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Included Components 3kW immersion heater T&P relief valve Acetal Tundish Inlet group control 2-port valve External expansion vessel Dual probe thermostat

Read more less

This is included in Telfords range of indirect heat pump cylinders, designed specifically to operate with a range of air source heat pumps. These are available in a range sizes between 150-500L capacity. They do not include a 3-port valve and this must be purchased separately.  Featuring a purpose-designed coil with a 2m² surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders are supplied with a factory-fitted 3 kW immersion heater to provide back-up heat. Duplex stainless steel provides superior corrosion resistance 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied (details below) Fully insulated to minimise any heat loss Twin coil option available for use with a traditional boiler and solar thermal Lifetime manufacturing warranty on inner container (2 years on components)* Renewable and bespoke options available Cylinder Specifications Capacity: 150L Weight (empty): 30kg Weight (full): 179kg Height: 1060mm Diameter: 510mm Coil size: 2m² Product Details Product code TSMI150/HP Standing heat loss 1.85 kWh/24h Max supply pressure 12bar Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Included Components 3kW immersion heater T&P relief valve Acetal Tundish Inlet group control 2-port valve External expansion vessel Dual probe thermostat

Read more less

This is a pre-plumbed Tempest cylinder built for use with a Samsung ASHP with an inbuilt 50 litre buffer. Featuring a purpose-designed coil with a large surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders have push-fit pre-fabricated pipework and wiring to assist with a fast and easy installation.  Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied Duplex stainless steel provides superior corrosion resistance White steel cased finish 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Fast reheat Factory-fitted temperature and pressure (T&P) relief value set Highly efficient Fully insulated to minimise any heat loss Lifetime manufacturing warranty on inner container (2 years on components)*   Cylinder Specifications Capacity: 300L Weight (empty): TDB Weight (full): TDB Height: 2115mm Diameter: 580mm Coil size: 3.3m² Product Details Product code TSMI300/50/HP/PREP/SAM Standing heat loss 1.82 kWh/24h Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Immersion heater 3kW Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump Filling loop Pressure gauge 15-22mm tundish 22mm inlet group valve Auto air vent

Read more less

This is a pre-plumbed Tempest cylinder built for use with a Samsung ASHP with an inbuilt 50 litre buffer. Featuring a purpose-designed coil with a large surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders have push-fit pre-fabricated pipework and wiring to assist with a fast and easy installation.  Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied Duplex stainless steel provides superior corrosion resistance White steel cased finish 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Fast reheat Factory-fitted temperature and pressure (T&P) relief value set Highly efficient Fully insulated to minimise any heat loss Lifetime manufacturing warranty on inner container (2 years on components)*   Cylinder Specifications Capacity: 250L Weight (empty): TDB Weight (full): TDB Height: 1921mm Diameter: 580mm Coil size: 3.3m² Product Details Product code TSMI250/50/HP/PREP/SAM Standing heat loss 1.71 kWh/24h Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Immersion heater 3kW Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump Filling loop Pressure gauge 15-22mm tundish 22mm inlet group valve Auto air vent

Read more less

This is a pre-plumbed Tempest cylinder built for use with a Samsung ASHP with an inbuilt 50 litre buffer. Featuring a purpose-designed coil with a large surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders have push-fit pre-fabricated pipework and wiring to assist with a fast and easy installation.  Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied Duplex stainless steel provides superior corrosion resistance White steel cased finish 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Fast reheat Factory-fitted temperature and pressure (T&P) relief value set Highly efficient Fully insulated to minimise any heat loss Lifetime manufacturing warranty on inner container (2 years on components)*   Cylinder Specifications Capacity: 200L Weight (empty): TDB Weight (full): TDB Height: 1716mm Diameter: 580mm Coil size: 3.3m² Product Details Product code TSMI200/50/HP/PREP/SAM Standing heat loss 1.64 kWh/24h Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Immersion heater 3kW Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump Filling loop Pressure gauge 15-22mm tundish 22mm inlet group valve Auto air vent

Read more less

This is a pre-plumbed Tempest cylinder built for use with a Samsung ASHP with an inbuilt 50 litre buffer. Featuring a purpose-designed coil with a large surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders have push-fit pre fabricated pipework and wiring to assist with a fast and easy installation.  Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied Duplex stainless steel provides superior corrosion resistance White steel cased finish 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Fast reheat Factory-fitted temperature and pressure (T&P) relief value set Highly efficient Fully insulated to minimise any heat loss Lifetime manufacturing warranty on inner container (2 years on components)*   Cylinder Specifications Capacity: 170L Weight (empty): TDB Weight (full): TDB Height: 1540mm Diameter: 580mm Coil size: 2.2m² Product Details Product code TSMI170/50/HP/PREP/SAM Standing heat loss 1.36 kWh/24h Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Immersion heater 3kW Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump Filling loop Pressure gauge 15-22mm tundish 22mm inlet group valve Auto air vent

Read more less

This is a pre-plumbed Tempest cylinder built for use with a Samsung ASHP with an inbuilt 50 litre buffer. Featuring a purpose-designed coil with a large surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders have push-fit pre fabricated pipework and wiring to assist with a fast and easy installation.  Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied Duplex stainless steel provides superior corrosion resistance White steel cased finish 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Fast reheat Factory-fitted temperature and pressure (T&P) relief value set Highly efficient Fully insulated to minimise any heat loss Lifetime manufacturing warranty on inner container (2 years on components)*   Cylinder Specifications Capacity: 150L Weight (empty): TDB Weight (full): TDB Height: 1500mm Diameter: 510mm Coil size: 2.2m² Product Details Product code TSMI150/50/HP/PREP/SAM Standing heat loss 1.36 kWh/24h Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Immersion heater 3kW Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump Filling loop Pressure gauge 15-22mm tundish 22mm inlet group valve Auto air vent

Read more less

High quality British manufactured stainless steel domestic hot water cylinder with 2m² coil, suitable for heat pumps up to 16kW. World Heat Climacyl cylinders are the standard diameter variant of World Heat heat pump cylinders.  Key features High quality stainless steel 25 Year manufacturing warranty on cylinder Highly insulated, part L compliant Dual immersion heaters (main immersion for heat pump legionella cycle, 2nd immersion for PV diverter connection) Full system unvented kits WRAS approved product ISO9001 certified quality management  Kit Includes Pressure reducing valve Expansion Vessel T & P Valve Drain Cock Air Vent 3 port valve 3kW Immerssion heater General Specifications Product Code 210CLIMACYLSS2 Capacity 210L Weight 50kg Weight full 260kg Height 1600mm Diameter 600mm Cylinder warranty 25 Years Parts warranty 1 Year Technical Specifications Hot and cold connectors 22mm Coil surface area 2m2 & 3m2 Standing Heat Loss 77.08W Expansion vessel size 18L ERP Band B

Read more less

High quality British manufactured stainless steel domestic hot water cylinder with 2m² coil, suitable for heat pumps up to 16kW. World Heat Climacyl cylinders are the standard diameter variant of World Heat heat pump cylinders.  Key features High quality stainless steel 25 Year manufacturing warranty on cylinder Highly insulated, part L compliant Dual immersion heaters (main immersion for heat pump legionella cycle, 2nd immersion for PV diverter connection) Full system unvented kits WRAS approved product ISO9001 certified quality management  Kit Includes Pressure reducing valve Expansion Vessel T & P Valve Drain Cock Air Vent 3 port valve 3kW Immerssion heater General Specifications Product Code 180CLIMACYLSS2 Capacity 180L Weight 45kg Weight full 225kg Height 1450mm Diameter 600mm Cylinder warranty 25 Years Parts warranty 1 Year Technical Specifications Hot and cold connectors 22mm Coil surface area 2m2 & 3m2 Standing Heat Loss 66.67W Expansion vessel size 12L ERP Band B

Read more less

These World Heat, Manchester manufactured, slimline pre-plumbed cylinder with a 50L integrated buffer is designed for a quick and easy installation of a Samsung air source heat pump. They provide a solution to unique jobs with specific space restrictions with capacities for 150L & 180L. This top quality product saves valuable installation time, helps prevent installation faults and is space efficient and neat. There is also the additional benefit on a 25 Year Manufacturing Warranty on the Stainless Vessel and a 12 Month Manufacturing Warranty on Components.  Key features High quality stainless steel cylinder that come with a 25 year manufacturing cylinder on the internal vessel Highly insulated, ERP rated and supplied with a full unvented kit. WRAS approved product with ISO9001 certified quality management.  These do not come with a primary circulation pump. Cylinder Specifications Capacity: 180L Weight (empty): 69.5kg Weight (full): 249.5kg Height: 2085mm Width: 475mm Diameter: 600mm Coil size: 2m² Product Details Product code 180SCYLPPSLIMMID Standing heat loss 69.3 W/h Re-heat time 35-45 mins Expansion vessel charge 3bar Mains inlet pressure 3bar Expansion relief valve 6bar T&P valve setting 7bar / 90 Deg. C Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump 2x 3kW immersion heaters (buffer & cylinder) Filling loop Pressure gauge 22mm tundish 22mm inlet group valve Buffer air vent

Read more less

These World Heat, Manchester manufactured, slimline pre-plumbed cylinder with a 50L integrated buffer is designed for a quick and easy installation of a Samsung air source heat pump. They provide a solution to unique jobs with specific space restrictions with capacities for 150L & 180L. This top quality product saves valuable installation time, helps prevent installation faults and is space efficient and neat. There is also the additional benefit on a 25 Year Manufacturing Warranty on the Stainless Vessel and a 12 Month Manufacturing Warranty on Components.  Key features High quality stainless steel cylinder that come with a 25 year manufacturing cylinder on the internal vessel Highly insulated, ERP rated and supplied with a full unvented kit. WRAS approved product with ISO9001 certified quality management.  These do not come with a primary circulation pump. Cylinder Specifications Capacity: 150L Weight (empty): 65.5kg Weight (full): 215.5kg Height: 1900mm Width: 475mm Diameter: 600mm Coil size: 2m² Product Details Product code 150SCYLPPSLIMMID Standing heat loss 64.58 W/h Re-heat time 35-45 mins Expansion vessel charge 3bar Mains inlet pressure 3bar Expansion relief valve 6bar T&P valve setting 7bar / 90 Deg. C Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump 2x 3kW immersion heaters (buffer & cylinder) Filling loop Pressure gauge 22mm tundish 22mm inlet group valve Buffer air vent

Read more less

These World Heat, Manchester manufactured, pre-plumbed cylinder with a 50L integrated buffer is designed for a quick and easy installation of a Samsung air source heat pump. This top quality product saves valuable installation time, helps prevent installation faults and is space efficient and neat. There is also the additional benefit on a 25 Year Manufacturing Warranty on the Stainless Vessel and a 12 Month Manufacturing Warranty on Components.  Key features High quality stainless steel cylinder that come with a 25 year manufacturing cylinder on the internal vessel Highly insulated, ERP rated and supplied with a full unvented kit. WRAS approved product with ISO9001 certified quality management.  These do not come with a primary circulation pump.    Cylinder Specifications Capacity: 300L Weight (empty): 88kg Weight (full): 388kg Height: 2020mm Width: 600mm Diameter: 650mm Coil size: 3m² Product Details Product code 180SCYLPPMID Standing heat loss 92.6 W/h Re-heat time 35-45 mins Expansion vessel charge 3bar Mains inlet pressure 3bar Expansion relief valve 6bar T&P valve setting 7bar / 90 Deg. C Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump 2x 3kW immersion heaters (buffer & cylinder) Filling loop Pressure gauge 22mm tundish 22mm inlet group valve Buffer air vent

Read more less

These World Heat, Manchester manufactured, pre-plumbed cylinder with a 50L integrated buffer is designed for a quick and easy installation of a Samsung air source heat pump. This top quality product saves valuable installation time, helps prevent installation faults and is space efficient and neat. There is also the additional benefit on a 25 Year Manufacturing Warranty on the Stainless Vessel and a 12 Month Manufacturing Warranty on Components.  Key features High quality stainless steel cylinder that come with a 25 year manufacturing cylinder on the internal vessel Highly insulated, ERP rated and supplied with a full unvented kit. WRAS approved product with ISO9001 certified quality management.  These do not come with a primary circulation pump.    Cylinder Specifications Capacity: 250L Weight (empty): 81kg Weight (full): 331kg Height: 2020mm Width: 550mm Diameter: 600mm Coil size: 3m² Product Details Product code 250SCYLPPMID Standing heat loss 90.4 W/h Re-heat time 35-45 mins Expansion vessel charge 3bar Mains inlet pressure 3bar Expansion relief valve 6bar T&P valve setting 7bar / 90 Deg. C Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump 2x 3kW immersion heaters (buffer & cylinder) Filling loop Pressure gauge 22mm tundish 22mm inlet group valve Buffer air vent

Read more less

These World Heat, Manchester manufactured, pre-plumbed cylinder with a 50L integrated buffer is designed for a quick and easy installation of a Samsung air source heat pump. This top quality product saves valuable installation time, helps prevent installation faults and is space efficient and neat. There is also the additional benefit on a 25 Year Manufacturing Warranty on the Stainless Vessel and a 12 Month Manufacturing Warranty on Components.  Key features High quality stainless steel cylinder that come with a 25 year manufacturing cylinder on the internal vessel Highly insulated, ERP rated and supplied with a full unvented kit. WRAS approved product with ISO9001 certified quality management.  These do not come with a primary circulation pump.    Cylinder Specifications Capacity: 210L Weight (empty): 75kg Weight (full): 285kg Height: 1820mm Width: 550mm Diameter: 600mm Coil size: 3m² Product Details Product code 210SCYLPPMID Standing heat loss 78.9 W/h Re-heat time 35-45 mins Expansion vessel charge 3bar Mains inlet pressure 3bar Expansion relief valve 6bar T&P valve setting 7bar / 90 Deg. C Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump 2x 3kW immersion heaters (buffer & cylinder) Filling loop Pressure gauge 22mm tundish 22mm inlet group valve Buffer air vent

Read more less

These World Heat, Manchester manufactured, pre-plumbed cylinder with a 50L integrated buffer is designed for a quick and easy installation of a Samsung air source heat pump. This top quality product saves valuable installation time, helps prevent installation faults and is space efficient and neat. There is also the additional benefit on a 25 Year Manufacturing Warranty on the Stainless Vessel and a 12 Month Manufacturing Warranty on Components.  Key features High quality stainless steel cylinder that come with a 25 year manufacturing cylinder on the internal vessel Highly insulated, ERP rated and supplied with a full unvented kit. WRAS approved product with ISO9001 certified quality management.  These do not come with a primary circulation pump.    Cylinder Specifications Capacity: 180L Weight (empty): 69.5kg Weight (full): 249.5kg Height: 1630mm Width: 550mm Diameter: 600mm Coil size: 2m² Product Details Product code 180SCYLPPMID Standing heat loss 69.30 W/h Re-heat time 35-45 mins Expansion vessel charge 3bar Mains inlet pressure 3bar Expansion relief valve 6bar T&P valve setting 7bar / 90 Deg. C Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump 2x 3kW immersion heaters (buffer & cylinder) Filling loop Pressure gauge 22mm tundish 22mm inlet group valve Buffer air vent

Read more less

These World Heat, Manchester manufactured, pre-plumbed cylinder with a 50L integrated buffer is designed for a quick and easy installation of a Samsung air source heat pump. This top quality product saves valuable installation time, helps prevent installation faults and is space efficient and neat. There is also the additional benefit on a 25 Year Manufacturing Warranty on the Stainless Vessel and a 12 Month Manufacturing Warranty on Components.  Key features High quality stainless steel cylinder that come with a 25 year manufacturing cylinder on the internal vessel Highly insulated, ERP rated and supplied with a full unvented kit. WRAS approved product with ISO9001 certified quality management.  These do not come with a primary circulation pump.    Cylinder Specifications Capacity: 150L Weight (empty): 65.5kg Weight (full): 215.5kg Height: 1505mm Width: 550mm Diameter: 600mm Coil size: 2m² Product Details Product code 150SCYLPPMID Standing heat loss 64.58 W/h Re-heat time 35-45 mins Expansion vessel charge 3bar Mains inlet pressure 3bar Expansion relief valve 6bar T&P valve setting 7bar / 90 Deg. C Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump 2x 3kW immersion heaters (buffer & cylinder) Filling loop Pressure gauge 22mm tundish 22mm inlet group valve Buffer air vent

Read more less

Controller for Bosch air source heat pump range. Suitable for 7001i AW and 7400i ranges. Product Number: 7738112314 Dimensions: 82 x 82 x 23 mm

Read more less

Indoor unit, suitable for new builds and renovations, The AWE are intended for assembly in a house and for connection to Compress 7001i AW/Compress 7400i AW heat pumps installed outdoors. Quiet, neat and compact they fit well into any home. Product number  7738602108 Height 700mm Width 485mm Depth 386mm Net Weight 32kg Warranty 2 years

Read more less

Indoor unit, suitable for new builds and renovations, The AWE are intended for assembly in a house and for connection to Compress 7001i AW/Compress 7400i AW heat pumps installed outdoors. Quiet, neat and compact they fit well into any home. Product number 7738602107 Height 700mm Width 485mm Depth 386mm Net Weight 32kg Warranty 2 years

Read more less

The quietest heat pump in Bosch's range, this premium unit is suitable for both new builds and renovations. It is designed as a monobloc unit with hermetically sealed refrigeration circuit for low maintenance and easy installation. The units boast A+++ at 35 degrees flow for heating and have additional cooling functionality from 15°C to 45°C. Quiet mark certified, they are notably quieter than other heat pumps on the market. Product number Outdoor Unit: 7738602075 MCS listed SCOPs @35°C 4.73 @40°C 4.35 @45°C 3.97 @50°C 3.62 @55°C 3.27 Heating nominal capacity 6kW Compressor type Twin rotary compressor Refrigerant Type R410A Refrigerant Volume 1.75kg Required flow rate 25.8L/m Heating up to 62°c Min operating temperature -18°c Max operating temperature 60°c Electricity Supply 230V 1N AC 50Hz Sound Power Level 50dBA Height 1380mm Width 940mm Depth 600mm Net Weight 113kg Warranty 2 years

Read more less

The quietest heat pump in Bosch's range, this premium unit is suitable for both new builds and renovations. It is designed as a monobloc unit with hermetically sealed refrigeration circuit for low maintenance and easy installation. The units boast A+++ at 35 degrees flow for heating and have additional cooling functionality from 15°C to 45°C. Quiet mark certified, they are notably quieter than other heat pumps on the market. Product number Outdoor Unit: 7738602075 MCS listed SCOPs @35°C 4.73 @40°C 4.35 @45°C 3.97 @50°C 3.62 @55°C 3.27 Heating nominal capacity 4kW Compressor type Twin rotary compressor Refrigerant Type R410A Refrigerant Volume 1.75kg Required flow rate 19.8L/m Heating up to 62°c Min operating temperature -18°c Max operating temperature 60°c Electricity Supply 230V 1N AC 50Hz Sound Power Level 50dBA Height 1380mm Width 940mm Depth 600mm Net Weight 113kg Warranty 2 years

Read more less

Suitable for new builds and renovations, the 7001i AW heat pumps are quality products with A+++ energy ratings. Quiet mark certified they are notably quieter than other heat pumps on the market. This has a 3-phase electrical input.  Product number Outdoor Unit: 7738601998 MCS listed SCOPs @35°C 3.55 @40°C 3.43 @45°C 3.51 @50°C 3.18 @55°C 2.85 Heating nominal capacity 10kW Compressor type Twin rotary compressor Refrigerant Type R410A Refrigerant Volume 4kg Required flow rate 48.60L/m Heating up to 62°c Min operating temperature -18°c Max operating temperature 60°c Electricity Supply 400V 3N AC, 50Hz Sound Power Level 53dBA Height 1695mm Width 1122mm Depth 545mm Net Weight 193kg Warranty 2 years

Read more less

Suitable for new builds and renovations, the 7001i AW heat pumps are quality products with A+++ energy ratings. Quiet mark certified they are notably quieter than other heat pumps on the market. Product number Outdoor Unit: 7738602089 MCS listed SCOPs @35°C 4.60 @40°C 4.27 @45°C 3.93 @50°C 3.65 @55°C 3.38 Heating nominal capacity 9kW Compressor type Twin rotary compressor Refrigerant Type R410A Refrigerant Volume 3.30kg Required flow rate 37.2L/m Heating up to 62°c Min operating temperature -17°c Max operating temperature 60°c Electricity Supply 230V 1N AC, 50Hz Sound Power Level 55 dBA Height 1695mm Width 1122mm Depth 545mm Net Weight 182kg Warranty 2 years

Read more less

Suitable for new builds and renovations, the 7001i AW heat pumps are quality products with A+++ energy ratings. Quiet mark certified they are notably quieter than other heat pumps on the market. Product number Outdoor Unit: 8738210257 MCS listed SCOPs @35°C 4.57 @40°C 4.34 @45°C 4.10 @50°C 3.77 @55°C 3.44 Heating nominal capacity 7.0kW Compressor type Twin rotary compressor Refrigerant Type R410A Refrigerant Volume 2.35kg Required flow rate 25.8L/m Heating up to 62°c Min operating temperature -18°c Max operating temperature 60°c Electricity Supply 230V 1N AC 50Hz Sound Power Level 48dBA Height 1380mm Width 930mm Depth 440mm Net Weight 114kg Warranty 2 years

Read more less

Suitable for new builds and renovations, the 7001i AW heat pumps are quality products with A+++ energy ratings. Quiet mark certified they are notably quieter than other heat pumps on the market. Product number Outdoor Unit: 8738210256 MCS listed SCOPs @35°C 4.77 @40°C 4.45 @45°C 4.12 @50°C 3.78 @55°C 3.43 Heating nominal capacity 5.0kW Compressor type Twin rotary compressor Refrigerant Type R410A Refrigerant Volume 1.75kg Required flow rate 19.8L/m Heating up to 62°c Min operating temperature -19°c Max operating temperature 60°c Electricity Supply 230V 1N AC 50Hz Sound Power Level 47 dBA Height 1380mm Width 930mm Depth 440mm Net Weight 107kg Warranty 2 years

Read more less

Suitable for new builds and renovations, the 7001i AW heat pumps are quality products with A+++ energy ratings. Quiet mark certified they are notably quieter than other heat pumps on the market. Product number Outdoor Unit: 8738210255 MCS listed SCOPs @35°C 4.41 @40°C 4.10 @45°C 3.80 @50°C 3.51 @55°C 3.22 Heating nominal capacity 4.0kW Compressor type Twin rotary compressor Refrigerant Type      R410A Refrigerant Volume 1.7kg Required flow rate 19.2L/m Heating up to 62°c Min operating temperature -18°c Max operating temperature  60°c Electricity Supply 230V 1N AC 50Hz Sound Power Level 47 dBA Height 1380mm Width 930mm Depth 440mm Net Weight 106kg Warranty 2 years

Read more less

Using your tablet or PC, you can operate your heat pump, make settings, and access the new ServiceWelt app using Stiebel Eltron's internet service gateway. It can be connected to the router of the home network, and there is also the option to control the system via a smartphone app. The device also enables communication with the Stiebel Eltron customer service centre. With time, the gateway will be expanded to include new services and appliance links. The most comprehensive and up-to-date information for this product can be found on the Stiebel Eltron TOOLBOX. Product Information Product name ISG web Product number 229336 Height 95mm Width 158mm Depth 37mm Warranty 7 years* *Standard 2 year warranty, extended to 7 for registered installers

Read more less

The WPKI-HK E is an insulated pump assembly for one heating circuit without a mixer, with an integral HE circulation pump and shut-off valves with thermometer and gravity-brake, including an opening mechanism. The assembly includes a white wall mounting bracket cover, and is suitable for a buffer cylinder or wall-mounted installation.  The most comprehensive and up-to-date information for this product can be found on the Stiebel Eltron TOOLBOX.   Product Information Product name WPKI-HK E Product number 233602 Head 7m Max throughput 3.3 m3/h Energy efficiency index 0.2 Connection top G 1 Connection bottom G 1 1/2 A Height 420mm Width 250mm Depth 269mm Warranty 7 years* *Standard 2 year warranty, extended to 7 for registered installers

Read more less

Corrosion-protected wall mounting support made from zinc-plated steel for on-site installation. Height adjustments can be made on the wall rail, while the appliance rail provides the possibility to align the appliance.  The most comprehensive and up-to-date information for this product can be found on the Stiebel Eltron TOOLBOX.   Product Information Product name WK 1 Product number 232963 Support length 740mm Weight 6.5kg Warranty 7 years* *Standard 2 year warranty, extended to 7 for registered installers

Read more less

White powder-coated bracket for installation on a strip foundation. Standard delivery includes: 2 pce incl. screws for securing the heat pump to the bracket. The most comprehensive and up-to-date information for this product can be found on the Stiebel Eltron TOOLBOX.   Product Information Product name SK 2 Product number 236693 Height 303mm Width 450mm Weight 6.5kg Warranty 7 years* *Standard 2 year warranty, extended to 7 for registered installers

Read more less

The remote control with room temperature sensor takes care of adjusting the set room temperatures. In addition, it switches between the day, setback and program operating modes. This remote control may be used in connection with WPM 3, WPM II, WPM 2.1 and WPMi for both heating circuits. The most comprehensive and up-to-date information for this product can be found on the Stiebel Eltron TOOLBOX.   Product Information Product name FE7 Product number 185579 Height 80mm Width 80mm Depth 30mm Warranty 7 years* *Standard 2 year warranty, extended to 7 for registered installers

Read more less