Google Shopping inverters and batteries

  Thermino i - Designed to produce domestic hot water by using an external heating source (e.g. a boiler) as a main source of heat, this range of heat batteries has a standby heating element built in to act as a backup if the main heat source fails. It can be used as an alternative to a hot water storage tank, providing the same energy storage in a much smaller volume. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 210 i would typically be installed in a 3 bedroom property. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty.   Power Inputs: Grid electricity Secondary Source Boiler Primary Source Solar Panels Heat Pump Some high temp General Specifications Product Code DNP-CBW-AVZ-1 Equivalent energy storage 10.5kWh Equivalent hot water capacity 212L Water available at 40°C 300L Weight in use 187kg Height 870mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 32.1W Energy efficiency rating A+ Recommended flow rate 20LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Connected load at 230v, 50hz 2,800W

Read more less

  Thermino i - Designed to produce domestic hot water by using an external heating source (e.g. a boiler) as a main source of heat, this range of heat batteries has a standby heating element built in to act as a backup if the main heat source fails. It can be used as an alternative to a hot water storage tank, providing the same energy storage in a much smaller volume. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 150 i would typically be installed in a 1-2 bedroom property. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty.   Power Inputs: Grid electricity Secondary Source Boiler Primary Source Solar Panels Heat Pump Some high temp General Specifications Product Code DKP-CBW-AVZ-1 Equivalent energy storage 7.0kWh Equivalent hot water capacity 142L Water available at 40°C 185L Weight in use 136kg Height 640mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 28.1W Energy efficiency rating A+ Recommended flow rate 15LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Connected load at 230v, 50hz 2,800W

Read more less

  Thermino i - Designed to produce domestic hot water by using an external heating source (e.g. a boiler) as a main source of heat, this range of heat batteries has a standby heating element built in to act as a backup if the main heat source fails. It can be used as an alternative to a hot water storage tank, providing the same energy storage in a much smaller volume. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 70 ePV would typically be installed in a studio apartment, or for off-grid applications in a caravan or boat. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty.   Power Inputs: Grid electricity Secondary Source Boiler Primary Source Solar Panels Heat Pump Some high temp   General Specifications Product Code DGP-CBW-AVZ-1 Energy capacity 3.2kWh Equivalent hot water capacity 71L Water available at 40°C 85L Weight in use 79kg Height 440mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 20W Energy efficiency rating C Recommended flow rate 6LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Connected load at 230v, 50hz 2,800W

Read more less

  Thermino ePV - Designed to produce domestic hot water by using grid electricity and surplus PV energy. It can be used as an alternative to a hot water storage tank, providing the same energy storage in a much smaller volume. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 300 ePV would typically be installed in a 4-5 bedroom property. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty.   Power Inputs:  Grid electricity - Secondary sourceBoilerSolar Panels - Primary SourceHeat Pump   General Specifications Product Code DRP-BAW-ATY-1 Equivalent energy storage 14.0kWh Equivalent hot water capacity 306L Water available at 40°C 436L Weight in use 233kg Height 1050mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 35W Energy efficiency rating C Recommended flow rate 25LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Annual electricity consumption 2,701kWh/annum

Read more less

Thermino ePV - Designed to produce domestic hot water by using grid electricity and surplus PV energy. It can be used as an alternative to a hot water storage tank, providing the same energy storage in a much smaller volume. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 210 e would typically be installed in a 3 bedroom property as a rule of thumb. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty.   Power Inputs:  Grid electricity - Secondary sourceBoilerSolar Panels - Primary SourceHeat Pump General Specifications Product Code SNP-BAW-ATY-1 Equivalent energy storage 10.5kWh Equivalent hot water capacity 212L Water available at 40°C 301L Weight in use 178kg Height 870mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 32W Energy efficiency rating C Recommended flow rate 20LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Annual electricity consumption 2,690kWh/annum  

Read more less

  Thermino ePV (UniQ eHW +iPV) - Designed to produce domestic hot water by using grid electricity and surplus PV energy. It can be used as an alternative to a hot water storage tank, providing the same energy storage in a much smaller volume. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 150 ePV would typically be installed in a 1-2 bedroom property as a rule of thumb. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty.   Power Inputs:  Grid electricity - Secondary sourceBoilerSolar Panels - Primary SourceHeat Pump General Specifications Product Code SKP-BAW-ATZ-1 Equivalent energy storage 7.0kWh Equivalent hot water capacity 140L Water available at 40°C 199L Weight in use 139kg Height 640mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 28.1W Energy efficiency rating C Recommended flow rate 15LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Annual electricity consumption 1,398kWh/annum

Read more less

Thermino 70 ePV - Designed to produce domestic hot water by using grid electricity and surplus PV energy. It can be used as an alternative to a hot water storage tank, providing the same energy storage in a much smaller volume. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 70 ePV would typically be installed in a studio apartment, or for off-grid applications in a caravan or boat. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty.   Power Inputs:  Grid electricity - Secondary sourceBoilerSolar Panels - Primary SourceHeat Pump General Specifications Product Code SGP-BAW-ATZ-1 Energy capacity 3.2kWh Equivalent hot water capacity 74L Water available at 40°C 105L Weight in use 79kg Height 440mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 20W Energy efficiency rating C Recommended flow rate 6LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Annual electricity consumption 542kWh/annum

Read more less

 Thermino e - Designed to produce domestic hot water and is heated directly by grid electricity only. This can be used as a space saving and flexible alternative to a hot water tank with an immersion heater. When combined with a charge timer and a variable electricity tariff, the Thermino e range allows for low cost electric water heating. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 300 e would typically be installed in a 4-5 bedroom property.   Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty. Power Inputs: Grid electricity Boiler Solar Panels Heat Pump   General Specifications Product Code DRP-AAW-AVZ-1 Equivalent energy storage 14.0kWh Equivalent hot water capacity 306L Water available at 40°C 436L Weight in use 233kg Height 1050mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 35W Energy efficiency rating C Recommended flow rate 25LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Annual electricity consumption 2,701kWh/annum

Read more less

  Thermino e - Designed to produce domestic hot water and is heated directly by grid electricity only. This can be used as a space saving and flexible alternative to a hot water tank with an immersion heater. When combined with a charge timer and a variable electricity tariff, the Thermino e range allows for low cost electric water heating. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 210 e would typically be installed in a 3 bedroom property as a rule of thumb. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty. Power Inputs: Grid electricity Boiler Solar Panels Heat Pump   General Specifications - Product Code SNP-AAW-AVZ-1 Equivalent energy storage 10.5kWh Equivalent hot water capacity 212L Water available at 40°C 301L Weight in use 178kg Height 870mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 32W Energy efficiency rating C Recommended flow rate 20LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Annual electricity consumption 2,690kWh/annum

Read more less

Thermino e - Designed to produce domestic hot water and is heated directly by grid electricity only. This can be used as a space saving and flexible alternative to a hot water tank with an immersion heater. When combined with a charge timer and a variable electricity tariff, the Thermino e range allows for low cost electric water heating. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 150 e would typically be installed in a 1-2 bedroom property as a rule of thumb. Note, the Sunamp is very heavy: Tilting it beyond 45 degrees may damage the unit and void your warranty. Power Inputs: Grid electricity Boiler Solar Panels Heat Pump   General Specifications Product Code SKP-AAW-AVZ-1 Equivalent energy storage 7.0kWh Equivalent hot water capacity 142L Water available at 40°C 199L Weight in use 139kg Height 640mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 28W Energy efficiency rating C Recommended flow rate 15LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Annual electricity consumption 1,398kWh/annum

Read more less

Thermino e - Designed to produce domestic hot water and is heated directly by grid electricity only. This can be used as a space saving and flexible alternative to a hot water tank with an immersion heater. When combined with a charge timer and a variable electricity tariff, the Thermino e range allows for low cost electric water heating. The reduced size combined with the fact that the Sunamp does not need any venting allows for full flexibility in install location. The Thermino 70 ePV would typically be installed in a studio apartment, or for off-grid applications in a caravan or boat. Note, the Sunamp is very heavy:   Tilting it beyond 45 degrees may damage the unit and void your warranty. Power Inputs: Grid electricity Boiler Solar Panels Heat Pump   General Specifications Product Code SGP-AAW-AVZ-1 Equivalent energy storage 3.2kWh Equivalent hot water capacity 74L Water available at 40°C 105L Weight in use 79kg Height 440mm Width 365mm Depth 575mm Storage core warranty 10 Years Other parts warranty 2 Years Technical Specifications Standing heat loss 20W Energy efficiency rating C Recommended flow rate 6LPM Minimum supply pressure 1.5 bar Maximum supply pressure 10 bar Annual electricity consumption 542kWh/annum

Read more less

Part No: SOLAX-BMS-HV-T58-2-11.6 Storage Systems - Li-ion Battery Pack This part is made up of the following items: 2 x HV11550-58-SLAVE-V2 SolaX Triple Power HV 5.8kWh LFP Extension Battery SLAVE V2   1 x SOLAX-BMS-PB SOLAX BMS Parallel Box   Package of: Solax BMS Parallel Box and SolaX Triple Power 5.8 Slave Battery The Solax BMS Parallel Box is an advanced battery management system that enables seamless parallel connection of multiple batteries, ensuring efficient energy utilisation and enhanced performance. With its cutting-edge technology and robust design, this parallel box is the ideal choice for residential and commercial applications. Included in Kit KIT-SOLAX-X1-3.0 Solax X1 3.0kW Hybrid Kit UK KIT-SOLAX-X1-3.6-AC SolaX 3.6kW AC Coupled Kit UK KIT-SOLAX-X1-5.0 Solax X1 5.0kW Hybrid Kit UK KIT-SOLAX-X3-10 Solax X3 10kW Hybrid Kit UK KIT-SOLAX-X3-8 Solax X3 8.0kW Hybrid Kit UK Weight:149.6 kg Battery Type:Lithium Ion Nominal Energy:11600 Wh Depth of discharge:90.00 % Voltage:230 V Continuous Discharge Rate (Normal Use):5750 W Maximum Discharge Rate (5 Minutes):3500 W Surge Discharge Rate (15 Seconds):800 W Maximum Charge Rate (5 Minutes):3500 W

Read more less

Part No: SE-BATTERY-4.6KWH Storage Systems - Li-ion Battery Pack SolarEdge Home Battery - Low Voltage 4.6kWh module BAT-05K48M0B-01 -Three Phase Inverter Connection Only   DC coupled battery featuring superior overall system efficiency, generating more energy to store and use for on-grid and backup* power application. Scalable solution that enables to stack up multiple battery modules per inverter for increased capacity (up to 23 kWh). Integrates seamlessly with the complete SolarEdge Home ecosystem, offering a single source for warranty, support and training, to streamlined logistics & operations. Solar, storage, EV charging, and smart devices all monitored and managed by a single app for optimized production, consumption, and backup* power. Includes enhanced safety features for battery protection. Simple plug and play installation, with automatic SetApp-based configuration   Weight:54.7 kg Battery Type:Lithium Ion Nominal Energy:4600 Wh Depth of discharge:90.00 % Voltage:48 V Continuous Discharge Rate (Normal Use):4096 W Maximum Discharge Rate (5 Minutes):4096 W Surge Discharge Rate (15 Seconds):4096 W Maximum Charge Rate (5 Minutes):2825 W

Read more less

Part No: X3-FIT-10 Storage Systems - Charger-Inverter Three Phase Retro Fit 10.0kW AC Coupled inverter Product Features Compatible with High voltage batteries IP65 protection rating Natural cooling and low maintenance Max Efficiency up to 96% This is the E version of the inverter with built in EPS function. It required external back up box to fully utilise the EPS function. It can be used with between 2 and 4 Solax Triple Power Batteries (one size batteries per system only) . This inverter can be paralleled up to 5 units per site. Looking to expand your system capacity? See Solax EPS Parallel Box options X3-PBOX-60kW-G2 – Connect up 6 hybrid inverters with a maximum of 60kW X3-PBOX-150kW-G2 – Connect up 10 hybrid inverters with a maximum of 150kW   Supplier Part No:X3-FIT 10.0 Charger Weight:38 kg Rated Power:10,000 W

Read more less

Part No: SE-5000H-NET-AC Storage Systems - Charger-Inverter AC coupled storage inverter with HD-Wave Technology and SetAPP  This inverter can be used directly with SolarEdge Energy Bank or with LG Chem RESU High Voltage battery when combined with StorEdge Interface STI-S4. SolarEdge energy meter and a suitable CT are required for the correct operation of the system. - AC coupling means it’s perfectly suited for sites with 1.      Three-phase SolarEdge PV inverters and 2.      Non-SolarEdge PV inverters or 3.      No PV at all. - Monitor battery status, PV inverter production, and self-consumption data for full visibility - IP65 – Outdoor and indoor installation Please note: This inverter does not have a display; commissioning needs to be done using Solar Edge SetAPP mobile application.   Supplier Part No:SE5000H-RWSACBEN4 Weight:10.96 kg Rated Power:5,000 W

Read more less

Part No: SE-5000H-APP-AC Storage Systems - Charger-Inverter AC coupled storage inverter with HD-Wave Technology and SetAPP  This inverter can be used directly with SolarEdge Energy Bank or with LG Chem RESU High Voltage battery when combined with StorEdge Interface STI-S4. SolarEdge energy meter and a suitable CT are required for the correct operation of the system. - AC coupling means it’s perfectly suited for sites with 1.      Three-phase SolarEdge PV inverters and 2.      Non-SolarEdge PV inverters or 3.      No PV at all. - Monitor battery status, PV inverter production, and self-consumption data for full visibility - IP65 – Outdoor and indoor installation Please note: This inverter does not have a display; commissioning needs to be done using Solar Edge SetAPP mobile application.   Supplier Part No:SE5000H-RWSACBNN4 Weight:10.96 kg Rated Power:5,000 W

Read more less

Part No: X1-AC-3.0 Storage Systems - Charger-Inverter X1 AC Charger Upgrade a PV system with the X1 AC Coupled Inverter Charger from SolaX. Compatible with any brand (single phase) inverter, the X1 retro-fit has a maximum efficiency of up to 97%, is rated for indoor or outdoor use and can be remotely monitored via the XCloud. Additional features: High voltage battery support means thinner cables are required 7.5kW Max charge/discharge Wifi or LAN stick available separately Suitable for grid trading applications with less than 0.5s response time Charging from grid possible Natural Cooling, quiet and low maintenance Please note the minimum number of batteries per X1 AC inverter is 1 and maximum of 3. Please note batteries need to be the same capacity, its not possible to connect both 4.5kWh and 6.3kWh to one inverter. UK only: This inverter has been tested and certified according to G98 or G99, but only for units having most recent Firmware and Hardware version. All Segen stock meets that criteria. Please note this item it is not ‘EN50438 Ireland’ certified and should not be installed in Republic of Ireland.   A LOT BETTER VALUE IF BOUGHT AS A PACKAGE   Supplier Part No:X1-AC-3.0 Charger Weight:18 kg Rated Power:3,000 W

Read more less

Part No: SE-3680H-NET-AC Storage Systems - Charger-Inverter AC coupled storage inverter with HD-Wave Technology and SetAPP  This inverter can be used directly with SolarEdge Energy Bank or with LG Chem RESU High Voltage battery when combined with StorEdge Interface STI-S4. SolarEdge energy meter and a suitable CT are required for the correct operation of the system. - AC coupling means it’s perfectly suited for sites with 1.      Three-phase SolarEdge PV inverters and 2.      Non-SolarEdge PV inverters or 3.      No PV at all. - Monitor battery status, PV inverter production, and self-consumption data for full visibility - IP65 – Outdoor and indoor installation Please note: This inverter does not have a display; commissioning needs to be done using Solar Edge SetAPP mobile application.   Supplier Part No:SE3680H-RWSACBEN4 Weight:7.8 kg Rated Power:3,680 W

Read more less

Part No: SE-3680H-APP-AC Storage Systems - Charger-Inverter AC coupled storage inverter with HD-Wave Technology and SetAPP  This inverter can be used directly with SolarEdge Energy Bank or with LG Chem RESU High Voltage battery when combined with StorEdge Interface STI-S4. SolarEdge energy meter and a suitable CT are required for the correct operation of the system. - AC coupling means it’s perfectly suited for sites with 1.      Three-phase SolarEdge PV inverters and 2.      Non-SolarEdge PV inverters or 3.      No PV at all. - Monitor battery status, PV inverter production, and self-consumption data for full visibility - IP65 – Outdoor and indoor installation Please note: This inverter does not have a display; commissioning needs to be done using Solar Edge SetAPP mobile application.   Supplier Part No:SE3680H-RWSACBNN4 Weight:7.8 kg Rated Power:3,680 W

Read more less

Part No: EN-IQ7A-72-M-INT-3PH Inverters - Micro Inverter Units Rating: 500W Phases: 3 This part is made up of the following items: 1 x EN-IQ7A-72-M-INT Enphase IQ7a 60/72 cell MC4 inegrated Microinverter 230VAC   PRODUCT FEATURES High performance version of the seventh-generation IQ platform Smart-Grid ready Easily integrated with the Gateway-S™ and Enphase™ monitoring and analysis software Easy to install thanks to lightweight design and improved two-wire cabling Double insulated housing, protection class II Modular design allows simple expansion of system as required Ultra reliable – system keeps working even if a single panel/microinverter fails or panel slips into shade Mobile app allows enhanced control and monitoring possibilities PRODUCT SPECIFICATION Commonly used module pairings: 295W - 460W + Module compatibility: 60-cell/120 half-cell and 72-cell/144 half-cell PV modules Peak output power: 366 VA Operating range: 18V - 58V IP Rating: IP67 Weight: 1.08 kg Rated Power: 500 W Min PPT Voltage: 38 V Max PPT Voltage: 43 V DC Startup Voltage: 33 V DC Shutdown Voltage: 32 V Max Input Voltage: 58 V Max DC Power: 500 W Max AC Power (5 Minutes): 366 W Surge AC Power (1 Second): 349 W Max DC Current: 10.2 A Max DC Inputs: 1 Has DC Fuses: 0 Connector: MC4   Included Connectors: 0 Euro Efficiency: 96.5 % Transformer: HF MPPT Quantity : 1 Has Integrated DC Switch: No Warranty: 25 years Enphase Energy, founded in 2006 in California, is the world leader in micro inverter technology with more than 13 million units sold worldwide and over 500,000 installed systems representing over 3GW of clean energy.

Read more less

Part No: EN-IQ7A-72-M-INT Inverters - Micro Inverter Units Rating: 349W Phases: 1 This new IQ7A micro inverter can work with 60 and 72 cell solar panels up to peak power of 366VA   Product Features: Most Powerful Enphase Microinverter on the market with high power output of 366VA The IQ7+ has a power rating of 295VA making the IQ7A the better choice Lower clipping losses resulting in higher net energy availability The higher the PV module rate, the wider the difference between IQ7+ and IQ7A making the IQ7A the ultimate microinverter It is noteworthy that clipping losses with IQ7A is almost zero until 500Wp Easy to install and light weight Built-in rapid shutdown Optimized for high powered 60 and 72 cell modules Class 11 double insulated IP67 enclosure Smart Grid ready Supplier Part No: IQ7A-72-M-INT Weight: 1.08 kg Rated Power: 349 W Min PPT Voltage: 18 V Max PPT Voltage: 58 V DC Startup Voltage: 33 V DC Shutdown Voltage: 18 V Max Input Voltage: 58 V Max DC Power: 460 W Max AC Power (5 Minutes): 366 W Surge AC Power (1 Second): 366 W Max DC Current: 15 A Max DC Inputs: 1 Has DC Fuses: 0 Connector: MC4   Included Connectors: 0 Euro Efficiency: 96.5 % Transformer: HF MPPT Quantity : 1 Has Integrated DC Switch: No Warranty: 25 years Enphase Energy, founded in 2006 in California, is the world leader in micro inverter technology with more than 13 million units sold worldwide and over 500,000 installed systems representing over 3GW of clean energy.

Read more less

Part No: EN-IQ7PLUS-72-M-INT-3PH Inverters - Micro Inverter Units Rating: 440W Phases: 3 This part is made up of the following items: 1 x  Enphase IQ7+ 60 and 72 cell MC4 integrated Microinverter 230 & 400VAC   PRODUCT FEATURES High performance version of the seventh-generation IQ platform Smart-Grid ready Easily integrated with the Gateway-S™ and Enphase™ monitoring and analysis software Easy to install thanks to lightweight design and improved two-wire cabling Double insulated housing, protection class II Modular design allows simple expansion of system as required Ultra reliable – system keeps working even if a single panel/microinverter fails or panel slips into shade Mobile app allows enhanced control and monitoring possibilities   PRODUCT SPECIFICATION Commonly used module pairings: 295W - 460W + Module compatibility: 60-cell/120 half-cell and 72-cell/144 half-cell PV modules Peak output power: 366 VA Operating range: 18V - 58V IP Rating: IP67 Weight: 1.05 kg Rated Power: 440 W Min PPT Voltage: 27 V Max PPT Voltage: 45 V DC Startup Voltage: 16 V DC Shutdown Voltage: 0 V Max Input Voltage: 60 V Max DC Power: 400 W Max AC Power (5 Minutes): 295 W Surge AC Power (1 Second): 290 W Max DC Current: 12 A Max DC Inputs: 1 Has DC Fuses: 0 Connector: MC4   Included Connectors: 0 Euro Efficiency: 96.5 % Transformer: HF MPPT Quantity : 1 Has Integrated DC Switch: No Warranty: 25 years Enphase Energy, founded in 2006 in California, is the world leader in micro inverter technology with more than 13 million units sold worldwide and over 500,000 installed systems representing over 3GW of clean energy.

Read more less

Part No: EN-IQ7PLUS-72-M-INT Inverters - Micro Inverter Units Rating: 290W Phases: 1 Enphase IQ 7+  Microinverter The high-powered smart grid-ready Enphase IQ 7+ Micro™  achieve the highest system efficiency.  Part of the Enphase IQ System, the IQ 7+ integrate seamlessly with the Enphase Envoy-S™, and the Enphase Enlighten™ monitoring and analysis software.  The IQ 7+ Micro extend the reliability standards set forth by previous generations and undergo over a million hours of power-on testing, enabling Enphase to provide an industry-leading warranty.   Easy to Install Lightweight and simple Faster installation with improved, lighter two-wire cabling The IQ7 inverters each come with a DC module connector included. We also stock of spares if required: partno EN-Q-DCC-2-INT. Productive and Reliable Optimized for high powered 60-cell and 72-cell modules More than a million hours of testing Class II double-insulated enclosure Smart Grid Ready Complies with advanced grid support, voltage and frequency ride-through requirements Remotely updates to respond to changing grid requirements Configurable for varying grid profiles   Please note, in order to comply with G98/G99 regulations, from 27th of April 2019 EVERY Enphase microinverter system requires Envoy device to commission the system AND it needs to be left on site permanently.   Please note you may receive a mix of INT and FR versions, functionality will not be affected as the Envoy will push the appropriate grid profile out to the microinverters regardless. Supplier Part No: IQ7PLUS-72-M-INT Weight: 1.05 kg Rated Power: 290 W Min PPT Voltage: 16 V Max PPT Voltage: 60 V DC Startup Voltage: 22 V DC Shutdown Voltage: 16 V Max Input Voltage: 60 V Max DC Power: 440 W Max AC Power (5 Minutes): 290 W Surge AC Power (1 Second): 290 W Max DC Current: 14 A Max DC Inputs: 1 Has DC Fuses: 0 Connector: MC4   Included Connectors: 1 Euro Efficiency: 96.5 % Transformer: HF MPPT Quantity : 1 Has Integrated DC Switch: No Warranty: 25 years Enphase Energy, founded in 2006 in California, is the world leader in micro inverter technology with more than 13 million units sold worldwide and over 500,000 installed systems representing over 3GW of clean energy.

Read more less

This is included in Telfords range of indirect heat pump cylinders, designed specifically to operate with a range of air source heat pumps. These are available in a range sizes between 150-500L capacity. They do not include a 3-port valve and this must be purchased separately.  Featuring a purpose-designed coil with a 2m² surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders are supplied with a factory-fitted 3 kW immersion heater to provide back-up heat. Duplex stainless steel provides superior corrosion resistance 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied (details below) Fully insulated to minimise any heat loss Twin coil option available for use with a traditional boiler and solar thermal Lifetime manufacturing warranty on inner container (2 years on components)* Renewable and bespoke options available   Cylinder Specifications Capacity: 250L Weight (empty): 40kg Weight (full): 288kg Height: 1800mm Diameter: 554mm Coil size: 3m² Product Details Product code TSMI250/HP Standing heat loss 2.00 kWh/24h Max supply pressure 12bar Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Included Components 3kW immersion heater T&P relief valve Acetal Tundish Inlet group control 2-port valve External expansion vessel Dual probe thermostat

Read more less

This is included in Telfords range of indirect heat pump cylinders, designed specifically to operate with a range of air source heat pumps. These are available in a range sizes between 150-500L capacity. They do not include a 3-port valve and this must be purchased separately.  Featuring a purpose-designed coil with a 2m² surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders are supplied with a factory-fitted 3 kW immersion heater to provide back-up heat. Duplex stainless steel provides superior corrosion resistance 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied (details below) Fully insulated to minimise any heat loss Twin coil option available for use with a traditional boiler and solar thermal Lifetime manufacturing warranty on inner container (2 years on components)* Renewable and bespoke options available Cylinder Specifications Capacity: 200L Weight (empty): 36kg Weight (full): 230kg Height: 1500mm Diameter: 554mm Coil size: 3m² Product Details Product code TSMI200/HP Standing heat loss 1.85 kWh/24h Max supply pressure 12bar Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Included Components 3kW immersion heater T&P relief valve Acetal Tundish Inlet group control 2-port valve External expansion vessel Dual probe thermostat

Read more less

This is included in Telfords range of indirect heat pump cylinders, designed specifically to operate with a range of air source heat pumps. These are available in a range sizes between 150-500L capacity. They do not include a 3-port valve and this must be purchased separately.  Featuring a purpose-designed coil with a 2m² surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders are supplied with a factory-fitted 3 kW immersion heater to provide back-up heat. Duplex stainless steel provides superior corrosion resistance 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied (details below) Fully insulated to minimise any heat loss Twin coil option available for use with a traditional boiler and solar thermal Lifetime manufacturing warranty on inner container (2 years on components)* Renewable and bespoke options available Cylinder Specifications Capacity: 170L Weight (empty): 34kg Weight (full): 202kg Height: 1200mm Diameter: 510mm Coil size: 2m² Product Details Product code TSMI170/HP Standing heat loss 1.94 kWh/24h Max supply pressure 12bar Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Included Components 3kW immersion heater T&P relief valve Acetal Tundish Inlet group control 2-port valve External expansion vessel Dual probe thermostat

Read more less

This is included in Telfords range of indirect heat pump cylinders, designed specifically to operate with a range of air source heat pumps. These are available in a range sizes between 150-500L capacity. They do not include a 3-port valve and this must be purchased separately.  Featuring a purpose-designed coil with a 2m² surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders are supplied with a factory-fitted 3 kW immersion heater to provide back-up heat. Duplex stainless steel provides superior corrosion resistance 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied (details below) Fully insulated to minimise any heat loss Twin coil option available for use with a traditional boiler and solar thermal Lifetime manufacturing warranty on inner container (2 years on components)* Renewable and bespoke options available Cylinder Specifications Capacity: 150L Weight (empty): 30kg Weight (full): 179kg Height: 1060mm Diameter: 510mm Coil size: 2m² Product Details Product code TSMI150/HP Standing heat loss 1.85 kWh/24h Max supply pressure 12bar Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Included Components 3kW immersion heater T&P relief valve Acetal Tundish Inlet group control 2-port valve External expansion vessel Dual probe thermostat

Read more less

This is a pre-plumbed Tempest cylinder built for use with a Samsung ASHP with an inbuilt 50 litre buffer. Featuring a purpose-designed coil with a large surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders have push-fit pre-fabricated pipework and wiring to assist with a fast and easy installation.  Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied Duplex stainless steel provides superior corrosion resistance White steel cased finish 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Fast reheat Factory-fitted temperature and pressure (T&P) relief value set Highly efficient Fully insulated to minimise any heat loss Lifetime manufacturing warranty on inner container (2 years on components)*   Cylinder Specifications Capacity: 300L Weight (empty): TDB Weight (full): TDB Height: 2115mm Diameter: 580mm Coil size: 3.3m² Product Details Product code TSMI300/50/HP/PREP/SAM Standing heat loss 1.82 kWh/24h Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Immersion heater 3kW Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump Filling loop Pressure gauge 15-22mm tundish 22mm inlet group valve Auto air vent

Read more less

This is a pre-plumbed Tempest cylinder built for use with a Samsung ASHP with an inbuilt 50 litre buffer. Featuring a purpose-designed coil with a large surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders have push-fit pre-fabricated pipework and wiring to assist with a fast and easy installation.  Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied Duplex stainless steel provides superior corrosion resistance White steel cased finish 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Fast reheat Factory-fitted temperature and pressure (T&P) relief value set Highly efficient Fully insulated to minimise any heat loss Lifetime manufacturing warranty on inner container (2 years on components)*   Cylinder Specifications Capacity: 250L Weight (empty): TDB Weight (full): TDB Height: 1921mm Diameter: 580mm Coil size: 3.3m² Product Details Product code TSMI250/50/HP/PREP/SAM Standing heat loss 1.71 kWh/24h Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Immersion heater 3kW Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump Filling loop Pressure gauge 15-22mm tundish 22mm inlet group valve Auto air vent

Read more less

This is a pre-plumbed Tempest cylinder built for use with a Samsung ASHP with an inbuilt 50 litre buffer. Featuring a purpose-designed coil with a large surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders have push-fit pre-fabricated pipework and wiring to assist with a fast and easy installation.  Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied Duplex stainless steel provides superior corrosion resistance White steel cased finish 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Fast reheat Factory-fitted temperature and pressure (T&P) relief value set Highly efficient Fully insulated to minimise any heat loss Lifetime manufacturing warranty on inner container (2 years on components)*   Cylinder Specifications Capacity: 200L Weight (empty): TDB Weight (full): TDB Height: 1716mm Diameter: 580mm Coil size: 3.3m² Product Details Product code TSMI200/50/HP/PREP/SAM Standing heat loss 1.64 kWh/24h Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Immersion heater 3kW Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump Filling loop Pressure gauge 15-22mm tundish 22mm inlet group valve Auto air vent

Read more less

This is a pre-plumbed Tempest cylinder built for use with a Samsung ASHP with an inbuilt 50 litre buffer. Featuring a purpose-designed coil with a large surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders have push-fit pre fabricated pipework and wiring to assist with a fast and easy installation.  Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied Duplex stainless steel provides superior corrosion resistance White steel cased finish 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Fast reheat Factory-fitted temperature and pressure (T&P) relief value set Highly efficient Fully insulated to minimise any heat loss Lifetime manufacturing warranty on inner container (2 years on components)*   Cylinder Specifications Capacity: 170L Weight (empty): TDB Weight (full): TDB Height: 1540mm Diameter: 580mm Coil size: 2.2m² Product Details Product code TSMI170/50/HP/PREP/SAM Standing heat loss 1.36 kWh/24h Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Immersion heater 3kW Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump Filling loop Pressure gauge 15-22mm tundish 22mm inlet group valve Auto air vent

Read more less

This is a pre-plumbed Tempest cylinder built for use with a Samsung ASHP with an inbuilt 50 litre buffer. Featuring a purpose-designed coil with a large surface area to allow maximum heat transfer of renewable energy into the stored water. Manufactured from Duplex stainless-steel, the cylinders have push-fit pre fabricated pipework and wiring to assist with a fast and easy installation.  Remote expansion vessel with factory-fitted wall mounting bracket Full unvented kit supplied Duplex stainless steel provides superior corrosion resistance White steel cased finish 316L grade stainless-steel 22mm compression fittings and coils Supplies mains pressure hot water and high flow rates Fast reheat Factory-fitted temperature and pressure (T&P) relief value set Highly efficient Fully insulated to minimise any heat loss Lifetime manufacturing warranty on inner container (2 years on components)*   Cylinder Specifications Capacity: 150L Weight (empty): TDB Weight (full): TDB Height: 1500mm Diameter: 510mm Coil size: 2.2m² Product Details Product code TSMI150/50/HP/PREP/SAM Standing heat loss 1.36 kWh/24h Max primary pressure 3bar T&P valve setting 7bar / 90 Deg. C Immersion heater 3kW Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump Filling loop Pressure gauge 15-22mm tundish 22mm inlet group valve Auto air vent

Read more less

High quality British manufactured stainless steel domestic hot water cylinder with 2m² coil, suitable for heat pumps up to 16kW. World Heat Climacyl cylinders are the standard diameter variant of World Heat heat pump cylinders.  Key features High quality stainless steel 25 Year manufacturing warranty on cylinder Highly insulated, part L compliant Dual immersion heaters (main immersion for heat pump legionella cycle, 2nd immersion for PV diverter connection) Full system unvented kits WRAS approved product ISO9001 certified quality management  Kit Includes Pressure reducing valve Expansion Vessel T & P Valve Drain Cock Air Vent 3 port valve 3kW Immerssion heater General Specifications Product Code 210CLIMACYLSS2 Capacity 210L Weight 50kg Weight full 260kg Height 1600mm Diameter 600mm Cylinder warranty 25 Years Parts warranty 1 Year Technical Specifications Hot and cold connectors 22mm Coil surface area 2m2 & 3m2 Standing Heat Loss 77.08W Expansion vessel size 18L ERP Band B

Read more less

High quality British manufactured stainless steel domestic hot water cylinder with 2m² coil, suitable for heat pumps up to 16kW. World Heat Climacyl cylinders are the standard diameter variant of World Heat heat pump cylinders.  Key features High quality stainless steel 25 Year manufacturing warranty on cylinder Highly insulated, part L compliant Dual immersion heaters (main immersion for heat pump legionella cycle, 2nd immersion for PV diverter connection) Full system unvented kits WRAS approved product ISO9001 certified quality management  Kit Includes Pressure reducing valve Expansion Vessel T & P Valve Drain Cock Air Vent 3 port valve 3kW Immerssion heater General Specifications Product Code 180CLIMACYLSS2 Capacity 180L Weight 45kg Weight full 225kg Height 1450mm Diameter 600mm Cylinder warranty 25 Years Parts warranty 1 Year Technical Specifications Hot and cold connectors 22mm Coil surface area 2m2 & 3m2 Standing Heat Loss 66.67W Expansion vessel size 12L ERP Band B

Read more less

These World Heat, Manchester manufactured, slimline pre-plumbed cylinder with a 50L integrated buffer is designed for a quick and easy installation of a Samsung air source heat pump. They provide a solution to unique jobs with specific space restrictions with capacities for 150L & 180L. This top quality product saves valuable installation time, helps prevent installation faults and is space efficient and neat. There is also the additional benefit on a 25 Year Manufacturing Warranty on the Stainless Vessel and a 12 Month Manufacturing Warranty on Components.  Key features High quality stainless steel cylinder that come with a 25 year manufacturing cylinder on the internal vessel Highly insulated, ERP rated and supplied with a full unvented kit. WRAS approved product with ISO9001 certified quality management.  These do not come with a primary circulation pump. Cylinder Specifications Capacity: 180L Weight (empty): 69.5kg Weight (full): 249.5kg Height: 2085mm Width: 475mm Diameter: 600mm Coil size: 2m² Product Details Product code 180SCYLPPSLIMMID Standing heat loss 69.3 W/h Re-heat time 35-45 mins Expansion vessel charge 3bar Mains inlet pressure 3bar Expansion relief valve 6bar T&P valve setting 7bar / 90 Deg. C Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump 2x 3kW immersion heaters (buffer & cylinder) Filling loop Pressure gauge 22mm tundish 22mm inlet group valve Buffer air vent

Read more less

These World Heat, Manchester manufactured, slimline pre-plumbed cylinder with a 50L integrated buffer is designed for a quick and easy installation of a Samsung air source heat pump. They provide a solution to unique jobs with specific space restrictions with capacities for 150L & 180L. This top quality product saves valuable installation time, helps prevent installation faults and is space efficient and neat. There is also the additional benefit on a 25 Year Manufacturing Warranty on the Stainless Vessel and a 12 Month Manufacturing Warranty on Components.  Key features High quality stainless steel cylinder that come with a 25 year manufacturing cylinder on the internal vessel Highly insulated, ERP rated and supplied with a full unvented kit. WRAS approved product with ISO9001 certified quality management.  These do not come with a primary circulation pump. Cylinder Specifications Capacity: 150L Weight (empty): 65.5kg Weight (full): 215.5kg Height: 1900mm Width: 475mm Diameter: 600mm Coil size: 2m² Product Details Product code 150SCYLPPSLIMMID Standing heat loss 64.58 W/h Re-heat time 35-45 mins Expansion vessel charge 3bar Mains inlet pressure 3bar Expansion relief valve 6bar T&P valve setting 7bar / 90 Deg. C Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump 2x 3kW immersion heaters (buffer & cylinder) Filling loop Pressure gauge 22mm tundish 22mm inlet group valve Buffer air vent

Read more less

These World Heat, Manchester manufactured, pre-plumbed cylinder with a 50L integrated buffer is designed for a quick and easy installation of a Samsung air source heat pump. This top quality product saves valuable installation time, helps prevent installation faults and is space efficient and neat. There is also the additional benefit on a 25 Year Manufacturing Warranty on the Stainless Vessel and a 12 Month Manufacturing Warranty on Components.  Key features High quality stainless steel cylinder that come with a 25 year manufacturing cylinder on the internal vessel Highly insulated, ERP rated and supplied with a full unvented kit. WRAS approved product with ISO9001 certified quality management.  These do not come with a primary circulation pump.    Cylinder Specifications Capacity: 300L Weight (empty): 88kg Weight (full): 388kg Height: 2020mm Width: 600mm Diameter: 650mm Coil size: 3m² Product Details Product code 180SCYLPPMID Standing heat loss 92.6 W/h Re-heat time 35-45 mins Expansion vessel charge 3bar Mains inlet pressure 3bar Expansion relief valve 6bar T&P valve setting 7bar / 90 Deg. C Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump 2x 3kW immersion heaters (buffer & cylinder) Filling loop Pressure gauge 22mm tundish 22mm inlet group valve Buffer air vent

Read more less

These World Heat, Manchester manufactured, pre-plumbed cylinder with a 50L integrated buffer is designed for a quick and easy installation of a Samsung air source heat pump. This top quality product saves valuable installation time, helps prevent installation faults and is space efficient and neat. There is also the additional benefit on a 25 Year Manufacturing Warranty on the Stainless Vessel and a 12 Month Manufacturing Warranty on Components.  Key features High quality stainless steel cylinder that come with a 25 year manufacturing cylinder on the internal vessel Highly insulated, ERP rated and supplied with a full unvented kit. WRAS approved product with ISO9001 certified quality management.  These do not come with a primary circulation pump.    Cylinder Specifications Capacity: 250L Weight (empty): 81kg Weight (full): 331kg Height: 2020mm Width: 550mm Diameter: 600mm Coil size: 3m² Product Details Product code 250SCYLPPMID Standing heat loss 90.4 W/h Re-heat time 35-45 mins Expansion vessel charge 3bar Mains inlet pressure 3bar Expansion relief valve 6bar T&P valve setting 7bar / 90 Deg. C Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump 2x 3kW immersion heaters (buffer & cylinder) Filling loop Pressure gauge 22mm tundish 22mm inlet group valve Buffer air vent

Read more less

These World Heat, Manchester manufactured, pre-plumbed cylinder with a 50L integrated buffer is designed for a quick and easy installation of a Samsung air source heat pump. This top quality product saves valuable installation time, helps prevent installation faults and is space efficient and neat. There is also the additional benefit on a 25 Year Manufacturing Warranty on the Stainless Vessel and a 12 Month Manufacturing Warranty on Components.  Key features High quality stainless steel cylinder that come with a 25 year manufacturing cylinder on the internal vessel Highly insulated, ERP rated and supplied with a full unvented kit. WRAS approved product with ISO9001 certified quality management.  These do not come with a primary circulation pump.    Cylinder Specifications Capacity: 210L Weight (empty): 75kg Weight (full): 285kg Height: 1820mm Width: 550mm Diameter: 600mm Coil size: 3m² Product Details Product code 210SCYLPPMID Standing heat loss 78.9 W/h Re-heat time 35-45 mins Expansion vessel charge 3bar Mains inlet pressure 3bar Expansion relief valve 6bar T&P valve setting 7bar / 90 Deg. C Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump 2x 3kW immersion heaters (buffer & cylinder) Filling loop Pressure gauge 22mm tundish 22mm inlet group valve Buffer air vent

Read more less

These World Heat, Manchester manufactured, pre-plumbed cylinder with a 50L integrated buffer is designed for a quick and easy installation of a Samsung air source heat pump. This top quality product saves valuable installation time, helps prevent installation faults and is space efficient and neat. There is also the additional benefit on a 25 Year Manufacturing Warranty on the Stainless Vessel and a 12 Month Manufacturing Warranty on Components.  Key features High quality stainless steel cylinder that come with a 25 year manufacturing cylinder on the internal vessel Highly insulated, ERP rated and supplied with a full unvented kit. WRAS approved product with ISO9001 certified quality management.  These do not come with a primary circulation pump.    Cylinder Specifications Capacity: 180L Weight (empty): 69.5kg Weight (full): 249.5kg Height: 1630mm Width: 550mm Diameter: 600mm Coil size: 2m² Product Details Product code 180SCYLPPMID Standing heat loss 69.30 W/h Re-heat time 35-45 mins Expansion vessel charge 3bar Mains inlet pressure 3bar Expansion relief valve 6bar T&P valve setting 7bar / 90 Deg. C Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump 2x 3kW immersion heaters (buffer & cylinder) Filling loop Pressure gauge 22mm tundish 22mm inlet group valve Buffer air vent

Read more less

These World Heat, Manchester manufactured, pre-plumbed cylinder with a 50L integrated buffer is designed for a quick and easy installation of a Samsung air source heat pump. This top quality product saves valuable installation time, helps prevent installation faults and is space efficient and neat. There is also the additional benefit on a 25 Year Manufacturing Warranty on the Stainless Vessel and a 12 Month Manufacturing Warranty on Components.  Key features High quality stainless steel cylinder that come with a 25 year manufacturing cylinder on the internal vessel Highly insulated, ERP rated and supplied with a full unvented kit. WRAS approved product with ISO9001 certified quality management.  These do not come with a primary circulation pump.    Cylinder Specifications Capacity: 150L Weight (empty): 65.5kg Weight (full): 215.5kg Height: 1505mm Width: 550mm Diameter: 600mm Coil size: 2m² Product Details Product code 150SCYLPPMID Standing heat loss 64.58 W/h Re-heat time 35-45 mins Expansion vessel charge 3bar Mains inlet pressure 3bar Expansion relief valve 6bar T&P valve setting 7bar / 90 Deg. C Buffer Vessel 50L (integrated) Included Components Samsung control board (MIM-E03EN) 3-port valve Secondary circulation pump 2x 3kW immersion heaters (buffer & cylinder) Filling loop Pressure gauge 22mm tundish 22mm inlet group valve Buffer air vent

Read more less

Controller for Bosch air source heat pump range. Suitable for 7001i AW and 7400i ranges. Product Number: 7738112314 Dimensions: 82 x 82 x 23 mm

Read more less

Indoor unit, suitable for new builds and renovations, The AWE are intended for assembly in a house and for connection to Compress 7001i AW/Compress 7400i AW heat pumps installed outdoors. Quiet, neat and compact they fit well into any home. Product number  7738602108 Height 700mm Width 485mm Depth 386mm Net Weight 32kg Warranty 2 years

Read more less

Indoor unit, suitable for new builds and renovations, The AWE are intended for assembly in a house and for connection to Compress 7001i AW/Compress 7400i AW heat pumps installed outdoors. Quiet, neat and compact they fit well into any home. Product number 7738602107 Height 700mm Width 485mm Depth 386mm Net Weight 32kg Warranty 2 years

Read more less

The quietest heat pump in Bosch's range, this premium unit is suitable for both new builds and renovations. It is designed as a monobloc unit with hermetically sealed refrigeration circuit for low maintenance and easy installation. The units boast A+++ at 35 degrees flow for heating and have additional cooling functionality from 15°C to 45°C. Quiet mark certified, they are notably quieter than other heat pumps on the market. Product number Outdoor Unit: 7738602075 MCS listed SCOPs @35°C 4.73 @40°C 4.35 @45°C 3.97 @50°C 3.62 @55°C 3.27 Heating nominal capacity 6kW Compressor type Twin rotary compressor Refrigerant Type R410A Refrigerant Volume 1.75kg Required flow rate 25.8L/m Heating up to 62°c Min operating temperature -18°c Max operating temperature 60°c Electricity Supply 230V 1N AC 50Hz Sound Power Level 50dBA Height 1380mm Width 940mm Depth 600mm Net Weight 113kg Warranty 2 years

Read more less

The quietest heat pump in Bosch's range, this premium unit is suitable for both new builds and renovations. It is designed as a monobloc unit with hermetically sealed refrigeration circuit for low maintenance and easy installation. The units boast A+++ at 35 degrees flow for heating and have additional cooling functionality from 15°C to 45°C. Quiet mark certified, they are notably quieter than other heat pumps on the market. Product number Outdoor Unit: 7738602075 MCS listed SCOPs @35°C 4.73 @40°C 4.35 @45°C 3.97 @50°C 3.62 @55°C 3.27 Heating nominal capacity 4kW Compressor type Twin rotary compressor Refrigerant Type R410A Refrigerant Volume 1.75kg Required flow rate 19.8L/m Heating up to 62°c Min operating temperature -18°c Max operating temperature 60°c Electricity Supply 230V 1N AC 50Hz Sound Power Level 50dBA Height 1380mm Width 940mm Depth 600mm Net Weight 113kg Warranty 2 years

Read more less

Suitable for new builds and renovations, the 7001i AW heat pumps are quality products with A+++ energy ratings. Quiet mark certified they are notably quieter than other heat pumps on the market. This has a 3-phase electrical input.  Product number Outdoor Unit: 7738601998 MCS listed SCOPs @35°C 3.55 @40°C 3.43 @45°C 3.51 @50°C 3.18 @55°C 2.85 Heating nominal capacity 10kW Compressor type Twin rotary compressor Refrigerant Type R410A Refrigerant Volume 4kg Required flow rate 48.60L/m Heating up to 62°c Min operating temperature -18°c Max operating temperature 60°c Electricity Supply 400V 3N AC, 50Hz Sound Power Level 53dBA Height 1695mm Width 1122mm Depth 545mm Net Weight 193kg Warranty 2 years

Read more less

Suitable for new builds and renovations, the 7001i AW heat pumps are quality products with A+++ energy ratings. Quiet mark certified they are notably quieter than other heat pumps on the market. Product number Outdoor Unit: 7738602089 MCS listed SCOPs @35°C 4.60 @40°C 4.27 @45°C 3.93 @50°C 3.65 @55°C 3.38 Heating nominal capacity 9kW Compressor type Twin rotary compressor Refrigerant Type R410A Refrigerant Volume 3.30kg Required flow rate 37.2L/m Heating up to 62°c Min operating temperature -17°c Max operating temperature 60°c Electricity Supply 230V 1N AC, 50Hz Sound Power Level 55 dBA Height 1695mm Width 1122mm Depth 545mm Net Weight 182kg Warranty 2 years

Read more less